Abstract:
Experiments for measuring high temperature full-field strain were conducted during GTAW welding process using digital image correlation (DIC) technology. A special visual...Show MoreMetadata
Abstract:
Experiments for measuring high temperature full-field strain were conducted during GTAW welding process using digital image correlation (DIC) technology. A special visual sensor system was equipped with image acquisition module. In order to reduce the influence of intense arc interference, a special laser-based illumination and filtering system was utilized. The in situ total strain close to the fusion line was measured during arc welding process. According to the total strain measured by DIC method and thermal strain calculated by the coefficient of thermal expansion, the mechanical strain was obtained, illustrating the sum of elastic and plastic strain distribution and deformation in the heated affected zone of the joint. Results showed that there remained compressive strain in both horizontal and vertical direction near the welding joint after welding. It demonstrated that full-field strain measurement could be achieved by DIC method during in situ arc welding.
Date of Conference: 08-10 July 2016
Date Added to IEEE Xplore: 07 November 2016
ISBN Information:
Electronic ISSN: 2162-7576
References is not available for this document.
Contents Select All
1.
S A David and T. Deb Roy, "Current issues and problems in welding science [J]", Science, vol. 257, no. 5069, pp. 497-502, 1992.
2.
P J Withers and H. Bhadeshia, "Residual stress. Part 1—measurement techniques[J]", Materials science and Technology, vol. 17, no. 4, pp. 355-365, 2001.
3.
R Knight and R W. Smith, "Residual stress in thermally sprayed coatings[C]", Thermal Spray Coat.: Res. Design Appl. and Proc. Natl. Spray Conf., pp. 607-12, 1993.
4.
H Murakawa, M BérešŔ, C M Davies et al., "Effect of low transformation temperature weld filler metal on welding residual stress[J]", Science and Technology of Welding & Joining, vol. 15, no. 5, pp. 393-399, 2010.
5.
W Zhang, Z Feng and P. Crooker, "Improved procedure for computing residual stresses from neutron diffraction data and its application to multipass dissimilar welds[J]", Science and Technology of Welding and Joining, vol. 16, no. 3, pp. 254-260, 2011.
6.
H Dai, J A Francis, H J Stone et al., "Characterizing phase transformations and their effects on ferritic weld residual stresses with X-rays and neutrons[J]", Metallurgical and Materials Transactions A, vol. 39, no. 13, pp. 3070-3078, 2008.
7.
R J Moat, H J Stone, A A Shirzadi et al., "Design of weld fillers for mitigation of residual stresses in ferritic and austenitic steel welds[J]", Science and Technology of Welding and Joining, vol. 16, no. 3, pp. 279-284, 2011.
8.
A Allen, C Andreani, M T Hutchings et al., "Measurement of internal stress within bulk materials using neutron diffraction[J]", NDT International, vol. 14, no. 5, pp. 249-254, 1981.
9.
S Spooner and X L. Wang, "Diffraction peak displacement in residual stress samples due to partial burial of the sampling volume[J]", Journal of applied crystallography, vol. 30, no. 4, pp. 449-455, 1997.
10.
V T Kowalski and A S. Voloshin, "Moire interferometry analysis of laser weld induced thermal strain[J]", Journal of Electronic Packaging, vol. 116, no. 3, pp. 177-183, 1994.
11.
S. Meguro and Y. Muramatsu, "Application of ESPI system to welding", Q. J. Jpn. Weld. Soc., vol. 24, no. 3, pp. 247-252, 2006.
12.
B Pan, K Qian, H Xie et al., "Two-dimensional digital image correlation for in-plane displacement and strain measurement: a review[J]", Measurement Science & Technology, vol. 20, no. 6, pp. 152-154, 2009.
13.
M De Strycker, P Lava, W Van Paepegem et al., "Measuring Welding Deformations with the Digital Image Correlation Technique[J]", Welding Journal, vol. 90, no. 6, pp. 107S-112S, 2011.
14.
M De Strycker, P Lava, W Van Paepegem et al., "Measuring Welding Deformations with the Digital Image Correlation Technique[J]", Welding Journal, vol. 90, no. 6, pp. 107S-112S, 2011.
15.
"welded DP780 steel joint under dynamic tensile loading[J]", Materials Science & Engineering A, vol. 627, pp. 296-305, 2015.
16.
Chen Jian, Yu Xinghua, Miller Roger G et al., "In-situ Thermal Strain and Temperature Measurement and Modeling during Arc Welding[J]", Science and Technology of Welding and Joining, vol. 20, 2015.
17.
B Pan, W U Da-Fang and Y. Xia, "Study of Speckle Pattern Quality Assessment used in Digital Image Correlation[J]", Journal of Experimental Mechanics, vol. 25, no. 2, pp. 120-129, 2010.
18.
D Lecompte, A Smits, S Bossuyt et al., "Quality assessment of speckle patterns for digital image correlation[J]", Optics & Lasers in Engineering, vol. 44, no. 11, pp. 1132-1145, 2006.
19.
J Blaber, B Adair and A. Antoniou, "Ncorr: Open-Source 2D Digital Image Correlation Matlab Software[J]", Experimental Mechanics, vol. 55, no. 6, pp. 1-18, 2015.
20.
P H. Hu, "Thermal deformation theory and application research in non-uniform temperature field of the mechanical components[D]", Hefei University of Technology, 2001.
21.
Dean Deng and Hidekazu Murakawa, "Numerical simulation of temperature field and residual stress in multi-pass welds in stainless steel pipe and comparison with experimental measurements[J]", Computational Materials Science, vol. 37, no. 3, pp. 269-277, 2006.
22.
M D Strycker, L Schueremans, W V Paepegem et al., "Measuring the thermal expansion coefficient of tubular steel specimens with digital image correlation techniques[J]", Optics & Lasers in Engineering, vol. 48, no. 10, pp. 978-986, 2010.
23.
Z Y Chen, H Lu, J M Chen et al., "Theoretic error analysis of strain measurement baased on digital image correlation method[J]", Welding, vol. 11, pp. 27-31, 2012.
24.
H W Schreier and M A. Sutton, "Systematic errors in digital image correlation due to undermatched subset shape functions[J]", Experimental Mechanics, vol. 42, no. 3, pp. 303-310, 2002.
25.
L B Meng, G C Jin and X F. Yao, "Application of iteration and finite element smoothing technique for displacement and strain measurement of digital speckle correlation[J]", Optics & Lasers in Engineering, vol. 45, no. 1, pp. 57-63, 2007.
26.
J H Wang and H. Lu, "Discussion on some issues of welding residual stress formation mechanism and eliminate principle[J]", Transactions of the China Welding Institution, vol. 23, no. 3, pp. 75-79, 2002.
